Sharp IQ-8000 Manuel d'installation télécharger pdf (Page 78)

7.10.2 Installation

To install the MX-485-2, it is necessary to mount the unit to a rigid service using #8 hardware in

four places. Care should be taken when selecting a mounting location to avoid sharp bends in

the connecting cables. Please note minimum bend radii of all fibers being used, to avoid

fracturing the fiber optic core.

7.10.2.1 PC Host to IQ-400 using Fiber Optics Converter Modules (RS485 Protocol)

Page lxv of 110 IQ-400 Installation Manual 33-10057-001-C

1 2 ... 73 74 75 76 77 78 79 80 81 82 83 ... 124 125

Installation Manual 1
33-10057-001 1
0.1 Board Diagrams 3
0.1.4 OUT Expansion Board 6
0.1.5 ALM Expansion Board 7
0.1.6 SAM Board 8
0.2 Table of Contents 9
1.0 Introduction 14
2.0 Unpacking the IQ-400 16
IQ-400 - Expansion Cable Plug 19
3.0 Installing Power 20
4.0 Wiring Your Readers 24
4.3.1 Procedure 25
4.4.1 Procedure 28
4.4.2.1 Procedure 28
5.0 Reader Connections 29
Option 1 34
Option 2 35
– Option 2 37
IQ-400 Board 38
Expansion Board 39
6.0 Wiring the Door(s) 46
6.6.3 SAM Board LED Arrays 56
Exit Sense Inputs 59
6.10.1 Procedure 61
7.1 Reset the IQ-400 Panel 62
7.5 Changing the Baud Rate 69
PCSC P/N: 04-10318-101 73
PCSC P/N: 04-10318-001 73
HyperTerminal 76
Protocol) 77
7.10.2 Installation 78
7.10.3 Optical Transmission 80
8.1 Status Lights 81
8.2 Communication Errors 82
8.2.2 Error Codes 83
(Pins 2-3) 86
8.8 User Selectable Options 91
8.9 Point Definitions 93
8.9.1 Sense Inputs 93
S3 through S6 are 94
IQ 4 PCB 94
8.9.2 Outputs 96
Connector 96
9.1 IQ-400 Features 99
9.1.3 Spare Parts- IQ-400 PCB 100
9.2.1 Electrical Ratings 101
9.2.2 Power Supply 101
9.2.3 Door Sense LEDs 102
9.2.5 Jumpers 102
9.3.2 System Capacities 104
9.3.3 Electrical Ratings 104
9.4.1 Electrical Ratings 106
9.4.2 Power Supply 106
9.4.3 Door Sense LEDs 107
9.4.5 Jumpers 107
9.5.1 System Capacities 109
9.5.2 Electrical Ratings 109
9.6.1 System Capacities 111
9.6.2 Electrical Ratings 111
9.6.3 Spare Parts- OUT PCB 111
9.7.1 System Capacities 112
9.7.2 Electrical Ratings 112
9.8 SAM Board 113
4-wire PCSC 114
5-wire Wiegand 114
9.10 Tool Requirements 115
10.1.1 Required Equipment: 118
10.1.2 Required Information: 118
10.1.3 Required firmware: 118
10.3.1 TCP/IP Configuration 121
10.4 Resetting the IQ-400E 124
End of Manual 125
PCSC, Inc 125
August 2008 125

Commentaires sur ces manuels

Pas de commentaire

Sharp IQ-8000 Manuel d'installation Page 78

Commentaires sur ces manuels

Produits connexes et manuels pour Composants des dispositifs de sécurité Sharp IQ-8000