Sharp IQ-8000 Manuel d'installation Page 102
- Page / 125
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
9.2.3 Door Sense LEDs
4 LEDs located at D17, D18, D19, and D20 indicate the status of the Door circuits. Resistors must be
installed at the door contacts, the switches in place, door closed (normal state), and the lines calibrated,
in order for the supervised inputs to function. See Step 4 for installation and calibration procedure.
LED Status Chart (for IQ-400 firmware I4+07.010.02 series):
•
Sense Input #25 LED is D17
•
Sense Input #27 LED is D18
•
Sense Input #29 LED is D19
•
Sense Input #31 LED is D20
NOTE LEDs D21-D24 are not used in the IQ-800.
OFF Circuit is in normal/secure state
ON Circuit is in an alarm condition state
Blinks once every 2 seconds Fault condition. Open circuit state
Blinks 1 time/second Fault condition. Short circuit state
Blinks 4 times/second Circuit is NOT calibrated and NOT in a functional state
9.2.4 Four-Reader Expansion Board- Active LEDs (P/N: 03-10102-301E)
4 LEDs located at D61, D62, D67, D68 indicate the status of the Reader circuits. When the LED blinks
momentarily after a card swipe, the system is processing the card data. The LED is normally off.
Reader LED Status:
•
Reader E LED is D61
•
Reader F LED is D62
•
Reader G LED is D67
•
Reader H LED is D68
9.2.5 Jumpers
Reader type is selected by the use of jumpers located in between the reader ports at W5 and W11-W14.
Refer to each diagram of reader-types on Section 5.0 [Reader Connections] for the proper setting of
these jumpers. Four other jumpers, located at W1, W2, W3, W6 and W15, designate chip selection, and
are set at the factory. They should not be changed unless directed by technical support.
The setting of the four jumpers at W5 (4W or 5W) determines how the jumpers next to each reader port
is set. Also, when using a 5-wire, 12VDC reader, you can control the voltage at PIN 1, by moving the
leftmost jumpers at W5 in conjunction with the reader port jumper setting (see Section 9.11.2 – next
page).
Page lxxxix of 110 IQ-400 Installation Manual 33-10057-001-C
- Installation Manual 1
- 33-10057-001 1
- 0.1 Board Diagrams 3
- 0.1.4 OUT Expansion Board 6
- 0.1.5 ALM Expansion Board 7
- 0.1.6 SAM Board 8
- 0.2 Table of Contents 9
- 1.0 Introduction 14
- 2.0 Unpacking the IQ-400 16
- IQ-400 - Expansion Cable Plug 19
- 3.0 Installing Power 20
- 4.0 Wiring Your Readers 24
- 4.3.1 Procedure 25
- 4.4.1 Procedure 28
- 4.4.2.1 Procedure 28
- 5.0 Reader Connections 29
- Option 1 34
- Option 2 35
- – Option 2 37
- IQ-400 Board 38
- Expansion Board 39
- 6.0 Wiring the Door(s) 46
- 6.6.3 SAM Board LED Arrays 56
- Exit Sense Inputs 59
- 6.10.1 Procedure 61
- 7.1 Reset the IQ-400 Panel 62
- 7.5 Changing the Baud Rate 69
- PCSC P/N: 04-10318-101 73
- PCSC P/N: 04-10318-001 73
- HyperTerminal 76
- Protocol) 77
- 7.10.2 Installation 78
- 7.10.3 Optical Transmission 80
- 8.1 Status Lights 81
- 8.2 Communication Errors 82
- 8.2.2 Error Codes 83
- (Pins 2-3) 86
- 8.8 User Selectable Options 91
- 8.9 Point Definitions 93
- 8.9.1 Sense Inputs 93
- S3 through S6 are 94
- IQ 4 PCB 94
- 8.9.2 Outputs 96
- Connector 96
- 9.1 IQ-400 Features 99
- 9.1.3 Spare Parts- IQ-400 PCB 100
- 9.2.1 Electrical Ratings 101
- 9.2.2 Power Supply 101
- 9.2.3 Door Sense LEDs 102
- 9.2.5 Jumpers 102
- 9.3.2 System Capacities 104
- 9.3.3 Electrical Ratings 104
- 9.4.1 Electrical Ratings 106
- 9.4.2 Power Supply 106
- 9.4.3 Door Sense LEDs 107
- 9.4.5 Jumpers 107
- 9.5.1 System Capacities 109
- 9.5.2 Electrical Ratings 109
- 9.6.1 System Capacities 111
- 9.6.2 Electrical Ratings 111
- 9.6.3 Spare Parts- OUT PCB 111
- 9.7.1 System Capacities 112
- 9.7.2 Electrical Ratings 112
- 9.8 SAM Board 113
- 4-wire PCSC 114
- 5-wire Wiegand 114
- 9.10 Tool Requirements 115
- 10.1.1 Required Equipment: 118
- 10.1.2 Required Information: 118
- 10.1.3 Required firmware: 118
- 10.3.1 TCP/IP Configuration 121
- 10.4 Resetting the IQ-400E 124
- End of Manual 125
- PCSC, Inc 125
- August 2008 125
Produits connexes et manuels pour Composants des dispositifs de sécurité Sharp IQ-8000
(14 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.071 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels