Sharp IQ-8000 Manuel d'installation Page 107
- Page / 125
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
9.4.3 Door Sense LEDs
8 LEDs located at D17, D18, D19, D20, D21, D22, D23, and D24 indicate the status of the Door circuits.
Resistors must be installed at the door contacts, the switches in place, door closed (normal state), and
the lines calibrated, in order for the supervised inputs to function. See Section 2.2.5.1.2 [Proper Point by
Point Calibration] of the LiNC-NET Administrator Guide (P/N: 38-10055-001) for calibration procedure.
LED Status Chart:
•
Sense Input #25 LED is D17
•
Sense Input #27 LED is D18
•
Sense Input #29 LED is D19
•
Sense Input #31 LED is D20
•
Sense Input #33 LED is D21
•
Sense Input #35 LED is D22
•
Sense Input #37 LED is D23
•
Sense Input #39 LED is D24
OFF Circuit is in normal/secure state
ON Circuit is in an alarm condition state
Blinks once every 2 seconds Fault condition. Open circuit state
Blinks 1 time/second Fault condition. Short circuit state
Blinks 4 times/second Circuit is NOT calibrated and NOT in a functional state
9.4.4 Eight-Reader Expansion Board (P/N: 03-10102-201E) - Active LEDs
Eight LEDs located at D49, D50, D55, D56, D61, D62, D67, D68 indicate the status of the Reader
circuits. When the LED blinks momentarily after a card swipe, the system is processing the card data.
The LED is normally off.
Reader LED Status:
•
Reader E LED is D49
•
Reader F LED is D50
•
Reader G LED is D55
•
Reader H LED is D56
•
Reader I LED is D61
•
Reader J LED is D62
•
Reader K LED is D67
•
Reader L LED is D68
9.4.5 Jumpers
Reader type is selected by the use of jumpers located in between the reader ports at W4-W5 and W7-
W14. Refer to each diagram of reader-types in Section 5 [Reader Connections] for the proper setting of
these jumpers. Four other jumpers, located at W1, W2, W3, W6, and W15 designate chip selection, and
are set at the factory. They should not be changed unless directed by technical support.
The setting of the jumpers at W4 and W5 (4W or 5W) determines how the jumpers next to each reader
port is set. Also, when using a 5-wire, 12VDC reader, you can control the voltage at PIN 1, by moving the
#3 jumpers at W4 and W5 in conjunction with the reader port jumper setting.
Page xciv of 110 IQ-400 Installation Manual 33-10057-001-C
- Installation Manual 1
- 33-10057-001 1
- 0.1 Board Diagrams 3
- 0.1.4 OUT Expansion Board 6
- 0.1.5 ALM Expansion Board 7
- 0.1.6 SAM Board 8
- 0.2 Table of Contents 9
- 1.0 Introduction 14
- 2.0 Unpacking the IQ-400 16
- IQ-400 - Expansion Cable Plug 19
- 3.0 Installing Power 20
- 4.0 Wiring Your Readers 24
- 4.3.1 Procedure 25
- 4.4.1 Procedure 28
- 4.4.2.1 Procedure 28
- 5.0 Reader Connections 29
- Option 1 34
- Option 2 35
- – Option 2 37
- IQ-400 Board 38
- Expansion Board 39
- 6.0 Wiring the Door(s) 46
- 6.6.3 SAM Board LED Arrays 56
- Exit Sense Inputs 59
- 6.10.1 Procedure 61
- 7.1 Reset the IQ-400 Panel 62
- 7.5 Changing the Baud Rate 69
- PCSC P/N: 04-10318-101 73
- PCSC P/N: 04-10318-001 73
- HyperTerminal 76
- Protocol) 77
- 7.10.2 Installation 78
- 7.10.3 Optical Transmission 80
- 8.1 Status Lights 81
- 8.2 Communication Errors 82
- 8.2.2 Error Codes 83
- (Pins 2-3) 86
- 8.8 User Selectable Options 91
- 8.9 Point Definitions 93
- 8.9.1 Sense Inputs 93
- S3 through S6 are 94
- IQ 4 PCB 94
- 8.9.2 Outputs 96
- Connector 96
- 9.1 IQ-400 Features 99
- 9.1.3 Spare Parts- IQ-400 PCB 100
- 9.2.1 Electrical Ratings 101
- 9.2.2 Power Supply 101
- 9.2.3 Door Sense LEDs 102
- 9.2.5 Jumpers 102
- 9.3.2 System Capacities 104
- 9.3.3 Electrical Ratings 104
- 9.4.1 Electrical Ratings 106
- 9.4.2 Power Supply 106
- 9.4.3 Door Sense LEDs 107
- 9.4.5 Jumpers 107
- 9.5.1 System Capacities 109
- 9.5.2 Electrical Ratings 109
- 9.6.1 System Capacities 111
- 9.6.2 Electrical Ratings 111
- 9.6.3 Spare Parts- OUT PCB 111
- 9.7.1 System Capacities 112
- 9.7.2 Electrical Ratings 112
- 9.8 SAM Board 113
- 4-wire PCSC 114
- 5-wire Wiegand 114
- 9.10 Tool Requirements 115
- 10.1.1 Required Equipment: 118
- 10.1.2 Required Information: 118
- 10.1.3 Required firmware: 118
- 10.3.1 TCP/IP Configuration 121
- 10.4 Resetting the IQ-400E 124
- End of Manual 125
- PCSC, Inc 125
- August 2008 125
Produits connexes et manuels pour Composants des dispositifs de sécurité Sharp IQ-8000
(14 pages)© 2020, manymanuals.fr. Tous droits réservés | 0.040 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels