Sharp AL-1000 Series Spécifications Page 1

FOR YOUR PROTECTION...To aid in reporting this compact copier in case of loss or theft, please record below the modelnumber and serial number located

9Installation2Be sure to allow the required spacearound the machine for servicing andproper ventilation.A small amount of ozone is produced within the

102InstallationCHECKING PACKED COMPONENTS ANDACCESSORIESOpen the carton and check if the following components and accessories are included.●If anythin

11Installation2REMOVING PROTECTIVE PACKING MATERIALS1Remove pieces of tape , , , , and and protective cover . Then openthe original cover and r

122Installation2Remove the CAUTION tape from the front cover and remove the two protective pinsfrom the fusing unit by pulling the strings upward one

13Installation26Gently insert the TD cartridge until it locks in place.7Close the front cover and then the side cover by pressing the round projection

142InstallationPaper guide BPaper guide A2Remove the pressure plate lock. Rotate the pressure plate lock in the direction ofthe arrow to remove it w

15Installation2LOADING COPY PAPER6Gently push the paper tray back into the copier.After loading copy paper, to cancel the blinking "P" witho

162InstallationPOWER ONTurn the power switch on the left side of the copier to the "ON" position. The ready ( )indicator will light up and o

17Making copies33MAKING COPIESThis chapter describes basic copying functions and some other copying functions using themanual bypass.PAPERFor best res

183Making copiesNORMAL COPYING1Ensure that paper of the desired size is set in the paper tray. See page 13, LOADINGCOPY PAPER. When copying onto 8-1/2

1CONTENTS1 GETTING STARTEDINTRODUCTION 3CAUTIONS 3MAIN FEATURES 4PART NAMES 6OPERATION PANEL 72 INSTALLATIONCOPIER INSTALLATION

19Making copies36Set the number of copies using the two copy quantity ( , ) keys.ZOOMTens digit Unit digit7Press the print ( ) key.Setting a large or

203Making copiesEXPOSURE ADJUSTMENT/PHOTO COPYINGCopy density adjustment is not required for most originals in the automatic exposure mode.To adjust t

21Making copies3REDUCTION/ENLARGEMENT/ZOOMPreset reduction and enlargementratios are: 50%, 64%, 78%, 129%, and200%When a zoom ( or ) key is pressed,

223Making copiesTWO-SIDED COPYINGTwo-sided copying can be made on this copier using the manual bypass.Example: The following two originals will be cop

23Special functions4SPECIAL FUNCTIONSDESCRIPTION OF SPECIAL FUNCTIONSThis chapter describes the special functions of this copier. Use these functions

244Special functionsTONER SAVE MODE2Press and hold down the exposure mode selector key for approximately 5 seconds.The manual ( ) indicator will go ou

25Special functions4USER PROGRAMS3Press the print ( ) key. The entered program number will be steadily lit and thecurrently selected parameter number

265Supplies and user maintenanceSUPPLIES AND USER MAINTENANCE5This chapter describes how to replace the TD cartridge and the drum cartridge and how to

27Supplies and user maintenance5TD CARTRIDGE REPLACEMENT3Install a new TD cartridge. To install the new cartridge, see page 11, INSTALLINGTHE TD CARTR

285Supplies and user maintenanceDRUM CARTRIDGE REPLACEMENT4Remove the new drum cartridge from the protective bag and remove the protectivecover from t

25SUPPLIES AND USER MAINTENANCE TD CARTRIDGE REPLACEMENT 26DRUM CARTRIDGE REPLACEMENT 27USER MAINTENANCE 28– Cabinet 28– Original tab

29Supplies and user maintenance5USER MAINTENANCETransfer chargerIf copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean

305Supplies and user maintenanceUSER MAINTENANCECopier lens cleaningIf white lines appear on copies in the direction of paper travel, make a reduction

31Copier trouble?66COPIER TROUBLE?This chapter describes misfeed removal and troubleshooting.MISFEED REMOVALWhen the misfeed ( ) indicator blinks or

326Copier trouble?MISFEED REMOVAL2Close the side cover by pressing the round projections near the side cover openbutton. The misfeed ( ) indicator wil

33Copier trouble?6MISFEED REMOVAL3Raise the fusing unit release lever and then close the side cover by pressing theround projections near the side cov

346Copier trouble?TROUBLESHOOTINGIf any problem occurs, check the list below before contacting the Sharp Service Center.See page:1516––182323362028293

35Copier trouble?6STATUS INDICATORSWhen the following indicators light up or blink on the operation panel or the followingalphanumeric codes appear in

366Copier trouble?AUTOMATIC EXPOSURE ADJUSTMENTThe automatic exposure level can be adjusted to suit your copying needs.1Press the exposure mode select

37Appendix7APPENDIX7SPECIFICATIONSType Digital copying machine, desk-top typeCopy system Dry, electrostatic transferOriginals Sheets, bound documentsO

387AppendixOPTION AND SUPPLY PART NUMBERS AND STORAGEWhen ordering supplies and option, please use the correct part numbers as listed below.Be sure to

31Getting Started1GETTING STARTEDThis chapter provides basic information for using the copier.INTRODUCTIONThis copier has been designed to provide int

39Appendix7MOVING INSTRUCTIONSWhen moving this copier, follow the procedure below.When moving this copier, be sure to remove the TD cartridge in advan

INDEXAAuto clear . . . . . . . . . . . . . . . . . . . . 23, 24Automatic exposure adjustment . . . . . . 36Auto power shut-off mode . . . . . . . .

INDEXPrint key . . . . . . . . . . . . . . . . . . . . . . . . 18Protective packing materials . . . . . . . . . 11RReady indicator . . . . . . . . .

MEMO

MEMO

MEMO

WARNING:FCC Regulations state that any unauthorized changes or modifications to this equipment not expressly approved by the manufacturer could void t

SHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135.SHARP CORPORATION© 1995 SHARP CORPORATIONPRINTED IN JAPANTINSE0067QSZZw

41Getting StartedSAFETY PRECAUTIONSThis Digital Copier is rated Class 1 and complies with 21 CFR 1040.10 and 1040.11 ofthe CDRH standards. This means

51Getting StartedMAIN FEATURESt Printer feature●This copier can be used as a laser printer by installing an optional printer upgrade kit.y Environment

61Getting StartedOriginal tableOperation panelPaper trayFront coverSide cover open buttonOriginal coverSide coverPower cord socketPower switchHandleHa

71Getting StartedOPERATION PANELq Exposure mode selector key andindicatorsUse to sequentially select the exposuremodes: AUTO, MANUAL or PHOTO.Selected

82InstallationINSTALLATIONFollow the installation procedure below to use the copier properly.COPIER INSTALLATIONImproper installation may damage the c