Sharp AL-1451 Spécifications Page 33
- Page / 126
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
AL-1551 OPERATIONAL DESCRIPTIONS 7-6
5) At this time, the paper is fed passed the paper entry detection switch
(PPD1), and detected by it. After about 0.15 sec from detection of
paper by PPD1, the tray paper feed solenoid (PFS) turns on so that
the clutch sleeve projection comes into contact with the paper feed
latch to stop the pick-up roller. Then the pick-up roller rotates for
about 0.15 sec so that the lead edge of the paper is evenly pressed
on the resist roller, preventing against skew feeding.
6) To release the resist roller, the tray paper feed solenoid and the resist
solenoid are turned on by the paper start signal to disengage the
resist start latch from the clutch sleeve, transmitting rotation of the
resist drive gear to the resist roller shaft. Thus the paper is
transported by the resist roller.
7) After the resist roller starts rotating, the paper is passed through the
pre-transfer guide to the transfer section. Images are transferred on
the paper, which is separated from the OPC drum by the drum curve
and the separation section.
8) The paper separated from the drum is passed through the fusing
paper guide, the heat roller (fusing section), POD (paper out
detector) to the copy tray.
(2) Manual multi paper feed operation
1) Before paper feed operation, the manual paper feed solenoid
(MPFS) is turned OFF as shown in the figure below.
2) When the PRINT button is pressed, the manual paper feed solenoid
(MPFS) turns on to disengage the manual paper feed latch.
A from the manual paper feed clutch sleeve A, rotating the manual
paper feed roller and the manual take-up roller. At the same time, the
manual paper feed stopper opens and the manual take-up roller is
pressed to the surface of the paper to start paper feeding.
ON
PFS
OFF
RRS
OFF
PFS
ON
RRS
OF
MPFS
F
C
A
ON
MPFS
A
C
- DIGITAL COPIER 1
- CAUTION 2
- CONTENTS 4
- [1] GENERAL 5
- [2] SPECIFICATIONS 6
- 3. Copy performance 8
- 4. Printer specifications 9
- [3] CONSUMABLE PARTS 10
- Production control 11
- 1. Appearance 12
- 2. Internal 12
- 1234567 891011 12 13
- 181716151413 13
- (AL-1551) 13
- 4. Motors and solenoids 14
- 5. Sensors and switches 15
- 6. PWB unit 16
- 7. Cross sectional view 17
- 1. Copier installation 18
- 2. Cautions on handling 18
- 4. Unpacking 19
- 4 or 5 times 20
- Paper guide (B) 20
- Paper guide (A) 20
- 8. Power to copier 21
- B. Windows 98: 22
- C. Windows Me/Windows 2000: 22
- D. Windows 3.1x: 22
- 10.Parallel interface 23
- [6] COPY PROCESS 24
- 2. Outline of print process 25
- 3. Actual print process 25
- About DC 5.2kV 26
- Process controlling 27
- [7] OPERATIONAL DESCRIPTIONS 28
- 2. Scanner section 29
- No Component Function 30
- (1) Heat roller 31
- (2) Separator pawl 31
- (3) Thermal control 31
- (4) Fusing resistor 31
- 7. SPF section 35
- C. Operational descriptions 36
- A. Initial state 36
- B. Front copy 36
- Upper Side of Gate 37
- Gate OFF 37
- Transfer 38
- Lock pawl rear 38
- Lock pawl front 38
- 2. Operation panel section 39
- 3. Optical section 40
- Thermistor 41
- PPD2 sensor 42
- Hearter lamp 42
- Heat roller 43
- B. Disassembly procedure 44
- Clutch unit 48
- Paper feed 48
- Wire treatment 49
- 7. Rear frame section 52
- 8. Power section 53
- A. Sensor PWB 54
- B. Pickup solenoid 54
- C. Clutch 54
- F. SPF motor 55
- G. Paper entry sensor 55
- 10.2nd cassette section 56
- D. Transport roller 57
- E. Paper feed clutch 57
- F. 2nd paper feed roller 57
- B. Cassette detection switch 57
- C. Paper feed solenoid 57
- (1) Remove the rear cabinet 58
- (2) Remove the shield plate 58
- (3) Remove the RSPF 59
- (1) Remove the clutch unit 60
- (2) Remove the clutch 60
- J. Transport unit removal 61
- K. Belt 1 61
- (1) Remove the parts 62
- (2) Remove the parts 63
- (1) Remove the reverse gate 64
- (2) Remove the solenoid 64
- Fixing Screws 65
- Set screw 66
- Scanner unit drive pulley 66
- LL and LR: 67
- Distance between the copy 67
- (1) Outline 68
- Shizuoka 69
- (1) Lead edge adjustment 70
- Lens unit number 70
- ( ) direction 70
- Reference line (0) 70
- (+) direction 70
- 2.0mm or less 71
- 2. Copy density adjustment 72
- Non toner 73
- Toner save 73
- The front edge of the 74
- Front edge of paper 74
- [10]SIMULATION, TROUBLE CODES 75
- 2. List of simulations 76
- 4. Trouble codes 88
- [11]USER PROGRAM 89
- [12]ELECTRICAL SECTION 90
- B. MCU PWB unit 91
- (1) CPU signal table 92
- (2) ASIC (Signal table) 94
- 3. Reset circuit 99
- A. Outline 100
- 5. Driver circuit (Solenoid) 101
- 7. Main motor drive circuit 101
- 8. Mirror motor circuit 102
- 9. Duplex motor circuit 102
- A. Block diagram 103
- (1) Main section 104
- (2) FW signal 105
- (3) Heater lamp drive circuit 105
- (4) High voltage section 105
- 11.CL invertor PWB (circuit) 106
- 13.Operation section 107
- [13]CIRCUIT DIAGRAM 108
- AL-1551 CIRCUIT DIAGRAM 13-2 109
- AL-1551 CIRCUIT DIAGRAM 13-3 110
- AL-1551 CIRCUIT DIAGRAM 13-4 111
- AL-1551 CIRCUIT DIAGRAM 13-5 112
- AL-1551 CIRCUIT DIAGRAM 13-6 113
- AL-1551 CIRCUIT DIAGRAM 13-7 114
- AL-1551 CIRCUIT DIAGRAM 13-8 115
- AL-1551 CIRCUIT DIAGRAM 13-9 116
- GDI MEMORY PWB (6MB) 117
- POWER SUPPLY (120V/127V) 118
- POWER SUPPLY (200V Series) 119
- ACTUAL WIRING DIAGRAM 1/5 120
- AL-1551 CIRCUIT DIAGRAM 13-14 121
- AL-1551 CIRCUIT DIAGRAM 13-15 122
- AL-1551 CIRCUIT DIAGRAM 13-16 123
- AL-1551 CIRCUIT DIAGRAM 13-17 124
- CAUTION FOR BATTERY DISPOSAL 125
- COPYRIGHT 126
- 2001 BY SHARP CORPORATION 126
Produits connexes et manuels pour Multifonctionnels Sharp AL-1451
Multifonctionnels Sharp AR-168N Spécifications
(177 pages)
(177 pages)
Elitegroup 258KA v.7 manuály
Uživatelské manuály a uživatelské příručky pro Notebooky Elitegroup 258KA v.7.
Poskytujeme 1 manuály pdf Elitegroup 258KA v.7 ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Elitegroup 258KA v.7 Uživatelský manuál (7 strany)
Značka: Elitegroup | Kategorie: Notebooks | Velikost: 0.05 MB |
Tabulka s obsahem
Další produkty a příručky pro Notebooky Elitegroup
| Modely | Typ Dokumentu |
|---|---|
| 258KA v.8 |
Uživatelský manuál
Elitegroup 258KA v.8 User Manual,
9 stránky
|
| 259EI |
Uživatelský manuál
Elitegroup 259EI Manuale d'uso,
97 stránky
|
| 257SA1 v.2 |
Uživatelský manuál
Elitegroup 257SA1 v.2 User Manual,
10 stránky
|
| 257SA1 v.3 |
Uživatelský manuál
Elitegroup 257SA1 v.3 User Manual,
13 stránky
|
| 257SA1 v.1 |
Uživatelský manuál
Elitegroup 257SA1 v.1 User Manual,
27 stránky
|
| 259EI |
Uživatelský manuál
Elitegroup 259EI Manual del usuario,
98 stránky
|
| 257SA1 v.4 |
Uživatelský manuál
Elitegroup 257SA1 v.4 User Manual [en] ,
12 stránky
|
| 257SA1 v.6 |
Uživatelský manuál
Elitegroup 257SA1 v.6 User Manual [en] [fr] ,
6 stránky
|
| 257SA1 v.8 |
Uživatelský manuál
Elitegroup 257SA1 v.8 User Manual,
9 stránky
|
| 257SA1 v.7 |
Uživatelský manuál
Elitegroup 257SA1 v.7 User Manual [en] [de] [fr] [it] ,
8 stránky
|
| 257SA1 v.5 |
Uživatelský manuál
Elitegroup 257SA1 v.5 User Manual,
17 stránky
|
| 257SA1 v.3 |
Uživatelský manuál
Elitegroup 257SA1 v.3 Manuel d'utilisation,
6 stránky
|
| 257SA1 v.4 |
Uživatelský manuál
Elitegroup 257SA1 v.4 Manuel d'utilisation,
12 stránky
|
| 257SA1 v.6 |
Uživatelský manuál
Elitegroup 257SA1 v.6 Manuel d'utilisation [en] ,
6 stránky
|
| 257SA1 v.5 |
Uživatelský manuál
Elitegroup 257SA1 v.5 Manuel d'utilisation [en] ,
17 stránky
|
| 257SA1 v.1 |
Uživatelský manuál
Elitegroup 257SA1 v.1 Manuel d'utilisation,
27 stránky
|
| 257SA1 v.7 |
Uživatelský manuál
Elitegroup 257SA1 v.7 Manuel d'utilisation [en] ,
8 stránky
|
| 257SA1 v.8 |
Uživatelský manuál
Elitegroup 257SA1 v.8 Manuel d'utilisation [en] ,
8 stránky
|
| 257SA1 v.3 |
Uživatelský manuál
Elitegroup 257SA1 v.3 Benutzerhandbuch [en] [es] [fr] ,
6 stránky
|
| 257SA1 v.5 |
Uživatelský manuál
Elitegroup 257SA1 v.5 Benutzerhandbuch [en] [ru] [es] [fr] ,
17 stránky
|
© 2020, manymanuals.fr. Tous droits réservés | 0.207 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels