Sharp AL-1451 Spécifications

Digital Laser Copier/PrinterOperation Manual MODELAL-1451

82Installation2INSTALLATIONFollow the installation procedure below to use the copier properly.COPIER INSTALLATIONImproper installation may damage the

92InstallationBe sure to allow the required space aroundthe machine for servicing and properventilation.A small amount of ozone is produced within the

102InstallationCHECKING PACKED COMPONENTS ANDACCESSORIESOpen the carton and check if the following components and accessories are included.CopierPower

112InstallationREMOVING PROTECTIVE PACKING MATERIALS1Remove all pieces of tape shown in the illustration below. Then open the originalcover and remove

122InstallationINSTALLING THE TD CARTRIDGE1Open the side cover while pressing the side cover open button.2Remove the CAUTION tape from the front cover

132InstallationINSTALLING THE TD CARTRIDGE5Gently insert the TD cartridge until it locks in place.6Close the front cover and then the side cover by p

142InstallationLOADING COPY PAPER2Remove the pressure plate lock. Rotate the pressure plate lock in the direction of thearrow to remove it while press

152InstallationLOADING COPY PAPER6Gently push the paper tray back into the copier.After loading copy paper, to cancel the blinking “P” without restart

162InstallationPOWER ONTurn the power switch on the left side of the copier to the “ON” position. The ready ( )indicator will light up and other indic

173Making copies3MAKING COPIESThis chapter describes basic copying functions and some other copying functions using themanual bypass.PAPERFor best res

FOR YOUR PROTECTION...To aid in reporting this compact copier in case of loss or theft, please record below the modelnumber and serial number located

183Making copiesNORMAL COPYINGThis copier has two document input stations - a single pass feeder (SPF) for automatic documentfeeding and an original t

193Making copiesNORMAL COPYINGZOOMTens digit Unit digitB. When using the original table:(1) Open the original cover.(2) Place an original face down on

203Making copiesNORMAL COPYING5Press the print ( ) key.●To display the number of copies made in a continuous run, press the leftcopy quantity key.●To

213Making copies3Use the light ( ) and dark ( ) keys to adjust the exposure level.If exposure level 2 is selected, the two left-handmost indicators fo

223Making copiesREDUCTION/ENLARGEMENT/ZOOM3Set the number of copies using the copy quantity ( , ) keys and press the print( ) key.BYPASS FEED (specia

233Making copiesTWO-SIDED COPYINGTwo-sided copying can be made on this copier using the manual bypass.Example: The following two originals will be cop

244Special functionsSPECIAL FUNCTIONSDESCRIPTION OF SPECIAL FUNCTIONSThis chapter describes the special functions of this copier. Use these functions

254Special functionsTONER SAVE MODE2Press and hold down the exposure mode selector key for approximately 5 seconds.The manual ( ) indicator will go ou

264Special functionsUSER PROGRAMS3Press the print ( ) key. The entered program number will be steadily lit and thecurrently selected parameter number

275Supplies and user maintenance5SUPPLIES AND USER MAINTENANCEThis chapter describes how to replace the TD cartridge and the drum cartridge.Be sure to

1CONTENTS1 GETTING STARTEDINTRODUCTION 3CAUTIONS 3MAIN FEATURES 4PART NAMES 6OPERATION PANEL 72 INSTALLATIONCOPIER INSTALLATION

285Supplies and user maintenanceTD CARTRIDGE REPLACEMENT3Install a new TD cartridge. To install the new cartridge, see page 12, INSTALLINGTHE TD CART

295Supplies and user maintenanceDRUM CARTRIDGE REPLACEMENT4Remove the new drum cartridge from the protective bag and remove the protectivecover from t

305Supplies and user maintenanceUSER MAINTENANCEProper care is essential in order to get clean, sharp copies. Be sure to take a few minutes toregularl

315Supplies and user maintenanceUSER MAINTENANCETransfer chargerIf copies start becoming streaky or blotchy, the transfer charger may be dirty. Clean

325Supplies and user maintenanceWhen copier is not in useTo prevent entry of dust and foreign matter, store the copier as follows.1Remove the power co

336Copier trouble?6COPIER TROUBLE?This chapter describes misfeed removal and troubleshooting.MISFEED REMOVALWhen the misfeed ( ) indicator blinks or

346Copier trouble?MISFEED REMOVALA Misfeed in the paper feed area1Gently remove the misfed paper from the paper feed area as shown in the illustratio

356Copier trouble?MISFEED REMOVAL●Do not touch the surface of the drum (green portion) of the drum cartridgewhen removing the misfed paper. Doing so m

366Copier trouble?3Rotate the feeding roller in the direction of the arrow and gently remove the misfedpaper from the exit area.Feeding roller4Raise t

376Copier trouble?MISFEED REMOVAL(B) Open the original cover and rotate the roller rotating knob to remove the misfed originalfrom the exit area.If th

25SUPPLIES AND USER MAINTENANCE TD CARTRIDGE REPLACEMENT 27DRUM CARTRIDGE REPLACEMENT 28USER MAINTENANCE 30– Cabinet 30– Original tab

386Copier trouble?TROUBLESHOOTINGIf any problem occurs, check the list below before contacting our Technical AssistanceDepartment.See page:1516––18242

396Copier trouble?STATUS INDICATORSWhen the following indicators light up or blink on the operation panel or the following alphanumericcodes appear in

406Copier trouble?AUTOMATIC EXPOSURE ADJUSTMENTThe automatic exposure level can be adjusted to suit your copying needs. This level is set forcopying f

417Appendix7APPENDIXSPECIFICATIONSType Digital laser copier/printer, desk-top typeCopy system Dry, electrostatic transferOriginals Sheets, bound docum

427AppendixMemory 6 MBPower supply AC 120V (±10%), 60 Hz (±2%)Power consumption 1,000 WOverall dimensions 23.9" (W) x 18.8" (D) (607 mm (W)

437AppendixSUPPLY PART NUMBERS AND STORAGEWhen ordering supplies, please use the correct part numbers as listed below.Be sure to use only genuine SHAR

447AppendixMOVING INSTRUCTIONSWhen moving this copier, follow the procedure below.When moving this copier, be sure to remove the TD cartridge in advan

INDEXAAuto clear . . . . . . . . . . . . . . . . . . . . 24, 25Automatic exposure adjustment . . . . . . 40Auto power shut-off mode . . . . . . . .

PPacked components . . . . . . . . . . . . . . . 10Paper– loading . . . . . . . . . . . . . . . . . . . . . . . . 13– special . . . . . . . . . . .

477AppendixMEMO

31Getting started1GETTING STARTEDThis chapter provides basic information for using the copier.INTRODUCTIONThis copier has been designed to provide int

487AppendixMEMO

For users in the USAThis device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not

PRINTED IN CHINA2001J KS TINSE0677QSZZSHARP ELECTRONICS CORPORATIONSharp Plaza, Mahwah, New Jersey 07430-2135.www.sharp-usa.comSHARP ELECTRONICS OF

41Getting startedCAUTIONS●Place the copier on a firm, level surface.●Do not install the copier in a humid or dusty location.●When the copier is not us

51Getting startedMAIN FEATURESSubstantial copying functions●Zoom copying from 50% to 200% in 1% increments can be performed.●Continuous copying of max

61Getting startedPART NAMESSPF exit area Original guidesFeeding roller coverDocumentfeeder trayTransfer chargerTD cartridge lock release buttonTD cart

71Getting startedOPERATION PANELExposure mode selector key andindicatorsUse to sequentially select the exposuremodes: AUTO, MANUAL or PHOTO.Selected m