Sharp DV-MX1U Manuel d'utilisateur télécharger pdf (Page 4)

4 LokSoundXL User Manual V2.1 05/2002

and coreless motors. It may be adjusted to the each

individual motor. Your locomotive will always keep

the selected speed, no matter how large the load is

or whether it is traveling up or down gradients.

Eight (!) function outputs: In addition to the two

lighting outputs, another six function outputs are

available for your choice of operation: you may

switch on smoke generators or interior lighting or

uncouple trains by pressing a key at your central

processing unit or hand held controller! With

blinking light effects and individually dimmable lamps

your trains look real and give you a lot of enjoyment.

Brake tracks: LokSoundXL decoders understand

(and react to) all available brake systems: besides

the Lenz brake generator, Märklin® brake track is

supported too.

Protecting functions: the motor output as well as

all function outputs are protected against overloads.

Analogue operation: LokSoundXL decoders may

be operated on AC- and DC systems without

problems.

Easy programming: Even with Märklin® 6021 all

functions may be changed easily without opening

the locomotive.

•A digital, two-tone sound module with unique

characteristics:

Prototype sounds: sounds of prototype loco-

motives were sampled using high quality

microphones and recorded digitally onto a memory

module. Thus your locomotives sound as accurate

as the prototype!

Two channels: in addition to steam impact or diesel

sounds, a further sound may be generated at the

same time. Steam whistles, bells, horns, etc. will

sound just like the original.

Steam, diesel and electric locomotive sounds are

possible: LokSoundXL may imitate every type of

locomotive you may think of. For each type of

locomotive there is a prototypical operational

sequence:

Steam locomotive: There are two, three and four-

cylinder steam locomotives, whose steam impacts

increase in frequency as the speed of the model

locomotive increases!

Diesel locomotive: The engine may be turned on

and off and rotates while stationary or driving based

upon the speed of the locomotive! The LokSoundXL

decoder may now also support Diesel electric

locomotives.

Characteristics of the LokSoundXL decoder

E-Locomotives: Historical electric locomotives

supply sound effects that are well worth listening

to: from the motion of the pantograph to the

clicking and cracking of the switchgear during

acceleration! Even a wheel synchronized squeaking

of the brakes is possible!

Sounds by pressing a key: Pressing a function key

(F1 to F12) emits the sounds!

Random noises: Both while stationary and while

moving, sounds such as air pump, water pump,

coal shovels, compressed air discharging, etc. at

random intervals controlled by you.

Chapter 3

Connection of the LokSoundXL decoders

3.1 Preparing installation of the decoder

The locomotive must be tested for excellent operation:

only a locomotive with impeccable mechanical

performance may take maximum advantage of the

decoder. A locomotive that does not perform

smoothly will not operate satisfactorily even with the

best decoder. Replace or clean worn out motor brushes,

check wheel contacts, bulbs etc.

Remove the locomotive from the track, disconnect

and isolate the motor. There must be NO electrical

contact between the motor and the rail pickup.

The LokSoundXL decoders have fixed dimensions;

make sure, that the decoder fits easily into the

locomotive. Do not use any pressure when replacing

the outer body onto the frame and touch no wires.

Further, make certain that flexible parts such as

transmissions and trucks are not obstructed by wires.

Fasten the decoder inside the locomotive with double

sided tape, hot glue or screws. The decoder gets very

warm during operation. Never pack the LokSound2XL

decoder in foam or similar materials. This impedes air

circulation and causes overheating.

The LokSoundXL Decoder comes as an open

circuit board that freatly reduces overheating.

Handle the LokSoundXL module with care.

Electronic components are sensitive to

electrostatic loads: always make sure that your

work place is grounded. If necessary, use an

earthed wristband.

1 2 3 4 5 6 7 8 9 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Sharp DV-MX1U Manuel d'utilisateur Page 4

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de DVD Sharp DV-MX1U