Sharp DV-MX1U Manuel d'utilisateur télécharger pdf (Page 16)

16 LokSoundXL User Manual V2.1 05/2002

•Dimmer: normal, continuously switched on load

•Blinking light: the output blinks with an adjustable

frequency

•Blinking light inverse: the output blinks as usual

but in opposite sequence.This permits to activate

blinking lights in opposite sequence (lamp1=on,

while lamp 2 = off and vice versa)

Starting with CV 114 each output has a CV that you

can program with the desired mode. Please note that

you may deactivate each output with "0" if not needed.

The light outputs are factory pre-set to "on". All

other function outputs AUX1 to AUX6 may be

switched off by factory default, depending on

the type of LokSoundXL-Decoder.

Dimming of lamps

With LokSoundXL you may dim the lamps in 15 steps

to adjust the brightness optimally to your model. The

lamps are pulsed, i.e.: they are continuously switched

on and off. The brightness of each output may be

adjusted separately. The desired dimming value (0 to

15) has to be added to the value of the corresponding

Control-CV (113 to 120) that defines the function

mode.

Blinking frequency and duration of "bright

phase"

If a function output has been set to "blinking" or

"blinking inverse", the duration of the "bright period"

(defines blinking frequency) and the on / off ratio

have to be taken from CV 121 (see paragraph 7.1).

The "bright period" is adjustable in 16 steps. It is always

a multiple of 0,184 sec.

The On / Off ratio is adjustable in 16 steps from 1/16

to 16/16. A ratio of 8/16 indicates that the light

output remains "on" for the same period as it is "off".

The value to be entered into the Control-CV 121 is

calculated as follows:

Duration of "On" period (value:0-15)*16+On/

Off ratio

Examples:

•Example 1: smoke generator at AUX1 and F5.

Let's assume you want to control a smoke generator

with function key F5 that should be connected to

output AUX1. Please refer to the installation

instructions in chapter 2.5. The output AUX1 must

be activated and assigned to the F5 key:

First we activate the output. In this example we

want to use the dimming function (the output must

be active continuously) and set at 100% brightness.

CV 115 controls output AUX1 (see paragraph 7.1).

The value to be entered into CV 115 is calculated as

follows: 16 (for dimming function) + 15 (for

maximum brightness) = 31.

Now we have to assign function key F5 to output

AUX1: see figure 12: Control-CV 39 controls the

F5 key (third column). In CV 39 we enter those

functions that should be switched with the F5-key.

We look at the table in figure 12, locate the

intersection of the row for F5 and column AUX1

and find the number (in this case 1). Once we enter

this value in CV 39 the F5key controls the output

AUX1.

•Example 2: blinking light at AUX6 and F8

We want to connect a “blinking light” to AUX6 and

control it via the F8 function key. The brightness

should be set to 6/15 of the maximum value. The

“bright period” and the “on / off” ratio are set as

described before

First we have to activate output AUX6 and set it to

“blinking”. We achieve this by entering 32 (for

blinking)+5(=6/15 of maximum brightness) =

37 in CV 120.

Next we assign output AUX6 to the F8 key. We

enter the functions to be controlled via F8 into CV

42. Again we consult the table in figure 12, find

the intersection between row F8 and column AUX6

and enter the number from the table in CV 42 (in

this case 32). Now the F8 key controls the output

AUX6

Please note that sound slot 6 and AUX6 output

are coupled: both the blinking light and sound,

memorized in sound slot 6, are activated and can

easily be modified using the LokProgrammer and

a PC.

•Example 3: Deceleration on / off with F5

Here we want to activate / deactivate the

acceleration/deceleration with F5. This function

represents a "logical" function and not a "physical"

output and thus does not have to be configured.

We only have to assign function "deactivate

deceleration" to the F5 key by entering value 4 in

CV 39 (see figure 12)

Diming the lamps

1 2 ... 11 12 13 14 15 16 17 18 19 20 21 ... 35 36

Commentaires sur ces manuels

Pas de commentaire

Sharp DV-MX1U Manuel d'utilisateur Page 16

Commentaires sur ces manuels

Produits connexes et manuels pour Lecteurs de DVD Sharp DV-MX1U