Sharp EL-1607P Spécifications télécharger pdf

WARNING

THE VOLTAGE USED MUST BE THE SAME AS SPECIFIED

ON THIS CALCULATOR. USING THIS CALCULATOR WITH

A HIGHER VOLTAGE THAN THAT WHICH IS SPECIFIED IS

DANGEROUS AND MAY RESULT IN A FIRE OR OTHER

TYPE

OF ACCIDENT CAUSING DAMAGE. WE ARE NOT

RESPONSIBLE

FOR ANY DAMAGE RESULTING FROM USE

OF THIS CALCULATOR WITH A VOLTAGE OTHER THAN

THAT WHICH IS SPECIFIED.

PRINTED IN CHINA

12DT(TINSE1647EHZZ)

To insure trouble-free operation of your SHARP calculator, we

recommend the following:

1. The calculator should be kept in areas free from extreme

temperature changes, moisture, and dust.

2. A soft, dry cloth should be used to clean the calculator. Do

not use solvents or a wet cloth.

3. Since this product is not waterproof, do not use it or store it

where fluids, for example water, can splash onto it.

Raindrops, water spray, juice, coffee, steam, perspiration, etc.

will also cause malfunction.

4. If service should be required, use only a SHARP servicing

dealer, a SHARP approved service facility or SHARP repair

service.

5. Do not wind the AC cord around the body or otherwise

forcibly bend or twist it.

6. Unplug the calculator by pulling on the plug portion, not the

cord.

7. Do not place objects on the AC cord. Do not run the AC cord

under rugs, mats, or other such objects.

8. This product, including accessories, may change due to

upgrading without prior notice.

SHARP will not be liable nor responsible for any incidental or

consequential economic or property damage caused by

misuse and/or malfunctions of this product and its

peripherals, unless such liability is acknowledged by law.

“•”: Set to the non-print mode.

“P”: Set to the print mode.

“P•IC”: Set to the print and item count mode.

For addition or subtraction, each time

is pressed, 1 is

added to the item counter, and each time

is pressed, 1

is subtracted.

• The count is printed when the calculated result is

obtained.

• Pressing of

, , or clears the counter.

Note: The counter has a maximum capacity of 3 digits (up to

±999). If the count exceeds the maximum, the counter will

recount from zero.

DECIMAL SELECTOR:

Presets the number of decimal places in the answer. In the ‘‘F’’

position, the answer is displayed in the floating decimal system.

CONSTANT/ADD MODE SELECTOR:

‘‘K’’: The following constant functions will be performed:

Multiplication:

The calculator will automatically remember the first number

entered (the multiplicand) and

instruction.

DISPLAY SYMBOLS:

M:A number has been stored in memory.

–:The display value is negative.

E:Error or overflow of capacity.

• : Appears when a number is in the grand total memory.

PAPER FEED KEY

LAST DIGIT CORRECTION KEY

GRAND TOTAL KEY

CLEAR ENTRY KEY

TOTAL KEY

MULTIPLICATION KEY

DIVISION KEY

MINUS EQUAL KEY

PLUS EQUAL KEY

CHANGE SIGN KEY

MARKUP KEY

MEMORY TOTAL CLEAR KEY

MEMORY SUBTOTAL RECALL KEY

TAX-INCLUDING KEY

PRE-TAX KEY

PERCENT KEY

NON-ADD/SUBTOTAL KEY:

Non-add – When this key is pressed right after an entry of

a number in the Print mode, the entry is printed

on the left-hand side with the symbol “#”.

This key is used to print out numbers not

subjects to calculation such as code, date, etc.

Subtotal – Used to get subtotal(s) of additions and/or

subtractions. When pressed following the

key, the subtotal is printed with the symbol

“

◊

” and the calculation may be continued.

By pressing this key even in the Non-print mode, the

displayed number is printed without any symbol.

CONVERSION KEY:

This key is used:

• to store the conversion rate.

• obtains a value by multiplying a given number with a

specified conversion rate.

• to recall the presently stored rate for check. Press

first to clear the calculation register and reset an error

condition, then press

. The conversion rate is printed

with the symbol “∆”.

CONVERSION KEY:

This key is used to obtain a value by dividing a given

number with a specified conversion rate.

Never insert paper roll if torn. Doing so will cause paper to

jam.

Always cut leading edge with scissors first.

1) Insert the leading edge of the paper roll into the opening.

(Fig. 1)

2) Turn the power on and feed the paper by pressing

(Fig. 2)

3) Lift the attached metal paper holder up and insert the paper

roll to the paper holder. (Fig. 3)

IMPORTANT

The wires in this mains lead are coloured in accordance with the following code:

BLUE: Neutral

BROWN: Live

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the

terminals in your plug proceed as follows,

The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured black.

The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured red.

This apparatus must be protected by a 3A fuse in the mains plug or distribution board.

“CAUTION: DO NOT CONNECT THE LIVE (BROWN) WIRE OR THE NEUTRAL (BLUE) WIRE TO THE EARTH TERMINAL AT

YOUR 3 PIN MAINS PLUG.”

USING THE CALCULATOR FOR

THE FIRST TIME

First, pull out the insulation sheet for the memory protection

battery (installed for retaining the tax/discount rate and conversion

rate information).

Removing the insulation sheet, and resetting

1. Pull out the insulation sheet for the memory protection

battery.

2. Connect the power supply plug to an outlet, then press the

RESET switch on the back of the unit after pressing the

power on switch.

(See “RESETTING THE UNIT”.)

POWER ON SWITCH:

When the “l” side of the power on switch is pressed, the

calculator is turned on.

OFF

POWER OFF KEY:

When the power off key is pressed, the calculator is

turned off.

EL-1607P

ELECTRONIC PRINTING CALCULATOR

OPERATION MANUAL

OPERATING CONTROLS

Division:

The calculator will automatically remember the second number

entered (the divisor) and

instruction.

‘‘•’’: Neutral

‘‘A’’: Use of the Add mode permits addition and subtraction of

numbers without an entry of the decimal point. When the

Add mode is activated, the decimal point is automatically

positioned according to the decimal selector setting.

Use of

, and will automatically override the Add mode

and decimally correct answers will be printed at the preset decimal

position.

ROUNDING SELECTOR:

“ ”: An answer is rounded up.

“5/4”: An answer is rounded off.

“

”: An answer is rounded down.

Note: The decimal point floats during successive calculation by

the use of

or .

If the decimal selector is set to “F” then the answer is always

rounded down (

GRAND TOTAL MODE SELECTOR:

“GT”: Grand Total

“•”: Neutral

STORE KEY:

This key is used to store the conversion rate or the tax/

discount rate.

Conversion rate:

• Enter the conversion rate, then press .

• A maximum of 6 digits can be stored (decimal point is not

counted as a digit).

Tax/discount rate:

• Enter the adding tax rate, then press .

• To store a discount rate, press

before pressing

• A maximum of 4 digits can be stored (decimal point is not

counted as a digit).

Note: • For the conversion rate and the tax/discount rate, a

single value can be stored for each. If you enter a new

rate, the previous rate will be cleared.

• The stored values for the conversion rate and the tax/

discount rate will be cleared if the power cable is

disconnected.

Cleaning the printing mechanism

If the print becomes dull after long time usage, clean the

printing wheel according to the following procedures:

1) Remove the printer cover and the ink roller.

2) Install the paper roll and feed it until it comes out of the front

of the printing mechanism.

3) Hold a small brush (like a tooth brush) lightly to the printing

wheel and clean it by pressing

4) Put back the ink roller and the printer cover.

Note: • Do not rotate the printing mechanism manually, this may

damage the printer.

PAPER ROLL REPLACEMENT

DO NOT PULL PAPER BACKWARDS AS THIS MAY CAUSE

DAMAGE TO PRINTING MECHANISM.

There are several situations which will cause an overflow or an error

condition. When this occurs, “E” will be displayed. The contents of

the memory at the time of the error are retained.

If an ‘‘0䡠E’’ is displayed at the time of the error, must be used to

clear the calculator. If an ‘‘E’’ with any numerals except zero is

displayed, the error may be cleared with

or and the

calculation can still be continued.

Also, in rare cases, printing may stop midway and the indication

“E” appear on the display. This is not a malfunction but is caused

when the calculator is exposed to strong electromagnetic noise or

static electricity from an external source. Should this occur, press

the

key and then repeat the calculation from the beginning.

Error conditions:

1. Entry of more than 12 digits or 11 decimals. This error can be

cleared with

or .

2. When the integer portion of an answer exceeds 12 digits.

3. When the integer portion of the contents of the memory

exceeds 12 digits.

(Ex.

999999999999 1 )

4. When any number is divided by zero.

(Ex. 5

0 )

EL-1607P(AW1)-1

➀

ERRORS

Time for battery replacement

Replace with a new battery once a year.

Method of battery replacement

Use one lithium battery (CR2032).

Notes:

•

When the battery is depleted, the set tax/discount rate,

conversion rate and the memory contents will be lost.

You may want to write down the tax/discount rate and

conversion rate, other important numbers on a sheet

of paper.

•

When replacing the battery, the set tax/

discount rate

and conversion rate, the memory contents will be lost.

•

The life of the pre-installed battery may be shorter

than expected because of the time the calculator

spends during shipment.

REPLACEMENT OF BATTERY FOR

MEMORY PROTECTION

Strong impacts, exposure to electrical fields, or other unusual

conditions may render the unit inoperative, and pressing the

keys will have no effect. If this occurs, you will have to press the

RESET switch on the bottom of the unit. The RESET switch

should be pressed only when:

• an abnormal event occurs and all keys are disabled.

• you install or replace the battery.

Notes:

• Pressing the RESET switch will clear the stored tax / discount

rate and conversion rate, other data stored in the memory.

• Use only a ballpoint pen to press the RESET switch. Do not

use anything breakable or anything with a sharp tip, such as a

needle.

• Connect the power supply plug to an outlet, then press the

RESET switch after pressing the power on switch. Check that

“0.” is displayed.

RESETTING THE UNIT

Operating capacity: 12 digits

Power supply: Operating:

AC: 220V–230V, 50Hz

Memory backup:

(DC)

(Lithium battery CR2032 × 1)

Memory Protection Battery lifespan:

Approx. 1 year. (tested and confirmed at 25°C (77°F); may

change due to usage environment)

PRINTING SECTION

Printer: Mechanical printer

Printing speed: Approx. 2.5 lines/sec.

(At temperature 25°C (77°F), when

“741•9 +” is printed. The printing speed will vary with the

number of rows and the figure types to be printed.)

Printing paper:

57 mm(2-1/4") - 58 mm(2-9/32") wide

80 mm(3-5/32") in diameter (max.)

Operating temperature:

0°C – 40°C (32°F – 104°F)

Power consumption: 59 mA

Automatic Power-off: Approx. 7 min.

Dimensions:

220 mm (W) × 303 mm (D) × 71.5 mm (H)

(8-21/32" (W) × 11-15/16" (D) × 2-13/16" (H))

Weight: Approx. 1.3 kg (2.87 Ib.) (with battery)

Accessories:

1 lithium battery (installed), 1 paper roll, 1 ink roller (installed),

and operation manual

Notes for handling Lithium batteries:

CAUTION

Danger of explosion if battery is incorrectly replaced.

Replace only with the same or equivalent type recommended

by the manufacturer.

Dispose of used batteries according to the manufacturer’s

instructions.

SPECIFICATIONS

PRINT / ITEM COUNT MODE SELECTOR:

WARNING

APPLYING INK TO WORN INK ROLLER OR USE OF

UNAPPROVED INK ROLLER MAY CAUSE SERIOUS

DAMAGE TO PRINTER.

1) Press the power off key.

2) Remove the printer cover. (Fig. 1)

3) Hold the top of the ink roller and remove the roller by

pulling it

toward you and then upward. (Fig. 2)

4) Install the new ink roller in the correct position. Make sure

that the roller is securely in place. (Fig. 3)

5) Put back the printer cover.

If printing is blurry even when the ink roller is in the proper

position, replace the roller.

Ink roller: Type EA-772R

INK ROLLER REPLACEMENT

After battery replacement

• Connect the power supply plug to an outlet and press the

power on switch.

Check that “0.” is displayed. If “0.” is not displayed, remove

the battery, reinstall it, and check the display again.

• Reset the tax / discount rate and conversion rate.

• In the box on the right, fill in the

month/year that you changed the

battery, as a reminder of when to

change it again.

Precautions on battery use

• Do not leave an exhausted battery

in the equipment.

•

Do not expose the battery to water

or flame, and do not take it apart.

• Store batteries out of the reach of

small children.

Fig. 2

1) Press the power off key and unplug the power supply plug

from the outlet.

2) Remove the battery cover on the back of the unit. (Fig. 1)

3) Remove the exhausted battery and install one new lithium

battery. Wipe the battery well with a dry cloth and place the

plus “+” side upward. (Fig. 2)

4) Replace the battery cover by reversing the removal

procedure.

5) Connect the power supply plug to an outlet, then press the

RESET switch on the back of the unit after pressing the power

on switch. (See “RESETTING THE UNIT”.)

Fig. 1

YearMonth

Fig. 1

Fig. 2

Fig. 3

Fig. 1

Fig. 2

Fig. 3

OPERATIONAL NOTES

EL-1607P(AW1)表面 12.5.31, 11:17 AMPage 1 Adobe PageMaker 6.0J/PPC

1 2

EL-1607P 1
CALCULATION EXAMPLES 2

Résumé du contenu

Page 1 - EL-1607P

WARNINGTHE VOLTAGE USED MUST BE THE SAME AS SPECIFIEDON THIS CALCULATOR. USING THIS CALCULATOR WITHA HIGHER VOLTAGE THAN THAT WHICH IS SPECIFIED ISDAN

Page 2 - CALCULATION EXAMPLES

CONSTANT62.35 × 11.11 =62.35 × 22.22 =62.35 62.35 62•35 ×11.11 11•11 =692•71 ✱692.7122.2222•22 =1,385•42 ✱1,385.4211.11 ⴓ 77.77 =22.22 ⴓ 77.77 =

Plus de documents pour Pompes à eau Sharp EL-1607P

Voir le document Sharp EL-1607P Spécifications

Sharp EL-1607P Spécifications (2 pages)

Commentaires sur ces manuels

Pas de commentaire

Sharp EL-1607P Spécifications

Naviguer en ligne ou télécharger Spécifications pour Pompes à eau Sharp EL-1607P. Sharp EL-1607P Specifications Manuel d'utilisatio

Résumé du contenu

Plus de documents pour Pompes à eau Sharp EL-1607P

Commentaires sur ces manuels

Produits connexes et manuels pour Pompes à eau Sharp EL-1607P