Sharp R-310BK Manuel de l'opérateur

R-310 Label Applicator Operator’s Manual Serial #

10 WEBBING THE R-310 Place the roll of labels on the unwind spool. Install the label disc and while pressing it against the label reel, tighten thumb

11 WASTE REMOVAL To remove waste web, turn off the machine, and remove the waste web retention clip. Tear the web as shown in Fig 5. While holding t

12 CARRIAGE ADJUSTMENT AND PRODUCT PLACEMENT SET CARRIAGE AS FOLLOWS 1. The product centerline should be slightly behind drive roller centerline (a

13 HORIZONTAL CARRIAGE ADJUSTMENT Using adjusting screws (see ‘D’ Fig 7), you may slide “Standard Carriage Assembly” left or right to improve or chan

14 VERTICAL CARRIAGE ADJUSTMENT This adjustment provides a means to relocate the lower carriage roller assembly into one of several pair of holes in

15 CARRIAGE ADJUSTMENT FOR TAPERED PRODUCTS A tapered product can be labeled on the R-310 by adjusting the carriage as follows. 1. Remove the tie ba

16 4. Place a product on the rollers and move the product and roller assembly so the product contacts the drive roll evenly. 5. Position the whole ca

17 PEELER PLATE ADJUSTMENT The peeler plate assembly may require adjustment with the change of label length or product diameter. A short label with a

18 ADJUST PEELER PLATE AS FOLLOWS 1. Using the provided 9/64” Allen wrench just loosen – DO NOT REMOVE - the two 8-32 SHCS located on the left side

19 SECTION 3 OPERATION TRI-TRONICS OPTICAL LABEL SENSOR Normal Label Opacity Autoset Button: This category includes most paper or metallized film l

2 Operator’s Manual Version: H 8/5/2004 The information in this manual is subject to change without notice. No part of this manual may be reprod

20 OPTIONAL LION SENSOR FOR CLEAR LABELS Important: • Web must remain in contact with mounting plate. • Label must pass under the sensor indicator

21 OFF DELAY The off delay dial is located on the front panel, below the on/off switch (see ‘A’ Fig 15). When the machine is cycled, the label sensor

22 TIMER ADJUSTMENT Select the product to be labeled and place it on the white carriage rollers. Move the product to the right against the bottle st

23 AIR ASSEMBLY ADJUSTMENTS Turn you attention to the underneath of the R-310. These two valves on the air regulator control the speed at which the

24 AIR REGULATOR Turn your attention to the side where the air regulator is mounted (see Fig 18). The Air Regulator is used to raise or lower the air

25 SECTION 4 MAINTENANCE GENERAL MAINTENANCE Drive rolls: The drive rolls must be kept clean. Wash with lacquer thinner or other recommended solve

26 SECTION 5 RECOMMENDED SPARE PARTS Part Number Description 100099 VALVE, 120VAC 3WY MAC AIR 100303 CYLINDER, 1" SPRING RETURN AIR 200009

27 SECTION 6 DRAWINGS AND BILL OF MATERIALS MAIN ASSEMBLY See Drawing 310-I-00H AIR CYLINDER MOUNTING ASSEMBLY See Drawing 310-I-10 FRONT PANEL ASSE

28 TECHNICAL SUPPORT When calling for Technical Support: Have your Model #: R-310H And the Serial Number ready (located on main base plate on th

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:MAIN ASSEMBLYMACHINE: R310310-I-00H*310-I-00H*01 SRL-500-42 BRACKET, OUTER BEARING 102 L-

3 Table of Contents SECTION 1 OVERVIEW...4 INTRODUCTION...

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:MAIN ASSEMBLYMACHINE: R310310-I-00H*310-I-00H*46 SRL-500-58 FOOT, EQUIPMENT (PACK OF 2)&g

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:MAIN ASSEMBLYMACHINE: R310310-I-00H*310-I-00H** SEE DRAWING** SRL-500-3306000 IS A STA

Bill of MaterialITEM NUM:PART NUMBER: PART DESCRIPTION: QTY:AIR CYLINDER MOUNTING ASSEMBLYR31001 100099 VALVE, 120VAC 3WY MAC AIR 102 100108 FTNG, MIN

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:FRONT PANEL ASSEMBLYMACHINE: R310310-I-20F*310-I-20F*01 200044 FUSE, AGC 5 A 102 200192-1

Bill of MaterialITEM NUM:PART NUMBER: PART DESCRIPTION: QTY:REGULATOR ASSEMBLYR31001 100300 REGULATOR, AIR 102 100229 OBSOLETE USE 100209 103 100217 O

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:LABEL SENSOR/PEELER ASSEMBLYMACHINE: R310310-I-40F*310-I-40F*01 MD-756 BAR, OPTICAL LABEL

4 SECTION 1 OVERVIEW INTRODUCTION Thank you for purchasing the R-310 semi-automatic round product label applicator. The R-310 is known for high qua

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:OPTIONAL STARWHEEL/PEELER ASSEMBLYMACHINE: R310310-I-41F*310-I-41F*01 855001 SHOULDER BOL

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:UPPER IDLER ROLL ASSEMBLYMACHINE: R310310-I-50E*310-I-50E*01 430180 BUSHING, 375 X 313 X

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:STANDARD CARRIAGE ASSEMBLYMACHINE: R310310-I-62*310-I-62*01 SRL-500-62A ASS'Y, IDLER

Bill of MaterialITEM NUM: PART NUMBER: PART DESCRIPTION: QTY:13" UNWIND ASSEMBLYMACHINE: R310UWA-13R-I-00*UWA-13R-I-00*01 UND-001 BAR, LABEL REEL

POWER MODULE SETUP SHEET PLEASE READ CAREFULLY BEFORE INSTALLING SWITCH #1 DELAY SELECT OFF - NO DELAY ON - START AND STOP DELAY SET BY FRONT PANE

5 UN-PACKING INSTRUCTIONS When the machine is received, the shipping carton will contain the following items (see Fig 1). 1. This Manual in a Manil

6 PRODUCT WARRANTY Universal Labeling Systems, Inc. warranties all parts to be free from defects in material and workmanship for a period of one year

7 SPECIFICATIONS Electrical Power: 120VAC +/- 10%, 5 Amps, 60Hz Compressed Air: Clean, Dry, 20-40PSI, 5CFM Product size: ½” to 6” (12.7mm

8 SECTION 2 SETUP ASSEMBLING THE R-310 The only item that needs to be added to the R-310 is the Unwind Assy. 1. Turn your attention to the back o

9 FUNCTION OF UNWIND ASSEMBLY The unwind is simple, but important to the operation of the R-310 machine. When the motor starts, the web and labels a