MODELPG-D3550WPG-D3050WPG-D2870WDATA PROJECTORSETUP MANUALConnecting Pin Assignments ... 2RS-

-10Operating the Projector Using the PJLinkTM ProtocolThe projector conforms with the PJLinkTM standard Class 1.The commands to be used in controlling

-11Setting up the Projector Network EnvironmentThis section describes the basic procedure for using the projector via the network.If the network is al

-121. Connecting the Projector to a ComputerEstablishing a one-to-one connection from the projector to a computer. Using a commercially available LAN

-132. Setting an IP Address for the ComputerThe following describes how to make settings in Windows Vista®.1 Log on the network using the administrat

-145 Click “Internet Protocol Version 4 (TCP/IPv4)”, and click the “Properties” button.6 Confi rm or change an IP address for the setup computer.1 Con

-153. Setting up a Network Con-nection for the ProjectorSettings for such items as the projector's IP address and subnet mask are compatible with

-164 The TCP/IP setting screen appears, ready for network settings for the projector.Items Setting example / RemarksNew PasswordYou can set the passw

-17Controlling the Projector via LANAfter connecting the projector to your network, enter the projector IP address in “Address” on Internet Explorer (

-18Confi rming the Projector Status (Status)2130On this screen, you can confi rm the projector status. You can confi rm the following items:MAC AddressPo

-19Setting and Adjusting the Projector (Settings & Adjustments)Example: “Picture” screen display for COMPUTER12On these screens, you can make proj

-2Connecting Pin AssignmentsCOMPUTER/COMPONENT input and COMPUTER/COMPONENT output Terminals: mini D-sub 15 pin female connectorCOMPUTER Input/Output

-20Making General Settings for the Network (Network - General)On this screen, you can make general settings relating to the network.Items DescriptionP

-21Controlling the Projector via LANSetting Error Items and Destination Addresses to which E-mail is to be Sent when an Error Occurs (Mail – Recipient

-22Resetting the Lamp Timer of the Projector via LANWhen the projector is connected to a network, you can use the communications program to send a com

-235 Click “Properties” on the “File” menu.6 Click the “Settings” tab, and then click “ASCII Setup”.7 Select the check boxes next to “Send line end

-24TroubleshootingCommunication cannot be established with the projectorWhen connecting the projector using serial-connection? Check that the RS-232C

-25? Take the following steps for checking the network settings for the computer.1. Open a command prompt.In the case of Windows® 2000: click “start”

-26? Check if the “TCP/IP” protocol is operating correctly using the “PING” command. Also, check if an IP address is set.1. Open a command prompt.In

-3RS-232C Cable recommended connection: D-sub 9 pin female connectorPin No. Signal Pin No. Signal1.2.3.4.5.6.7.8.9.CDRDSDERSGDRRSCSCI1.2.3.4.5.6.7.8.9

-4RS-232C Specifi cations and CommandsComputer controlA computer can be used to control the projector by connecting an RS-232C serial control cable (cr

-5CommandsExample: When turning on the projector, make the following setting.Computer ProjectorPOWR___1omOKCONTROL CONTENTS COMMAND PARAMETERRETURNPow

-6CONTROL CONTENTS COMMAND PARAMETERRETURNPower ONStandby mode(or 30-second startup time)Resize S-VIDEO Normal R A S V___1 OK or ERR ERR16:9 R A S V__

-7CONTROL CONTENTS COMMAND PARAMETERRETURNPower ONStandby mode(or 30-second startup time)HDMI Input Picture Mode Standard R C P S__10OK or ERR ERRPres

-8CONTROL CONTENTS COMMAND PARAMETERRETURNPower ONStandby mode(or 30-second startup time)C.M.S. Setting On C M C S__11OK or ERR ERROff C M C S__00OK o

-9CONTROL CONTENTS COMMAND PARAMETERRETURNPower ONStandby mode(or 30-second startup time)Language English M E L A___1 OK or ERR ERRDeutsch M E L A___2