Sharp R-370ES Manuel de l'opérateur Page 10
- Page / 30
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
10
CS-370
PREPARATION FOR USE
Bolt (A)
Dimple (D)
Recess (E)
Front hole (C)
Rear
hole (B)
Nut (F)
Guide bar
Kick Guard
®
Brake connector
Clutch cover
Brake lever
(Front hand guard)
Two nuts
WARNING
Saw chain is sharp! Always wear gloves
when handling assembly, otherwise serious
personal injury may result.
KICK GUARD
®
TO BAR
INSTRUCTIONS
Tools Needed: Two 11 mm Wrenches.
For saws with Kick Guard
®
P/N 2893201 and
Symmetrical Low-Kick type (Double Guard)
guide bars.
1. Install bolt (A) in
rear
hole (B) of Kick Guard
®
and through front hole (C) in guide bar.
2. IMPORTANT: Dimple (D) in Kick Guard
®
must
engage recess (E) in guide bar.
3. Tighten nut (F) and bolt (A) using 11 mm
wrenches until snug. Make certain Kick Guard
®
is flush against guide bar.
4. Tighten nut (F) 1/8 additional turn.
5. Check to make certain Kick Guard
®
is tight on
guide bar.
GUIDE BAR AND SAW CHAIN
INSTALLATION/REMOVAL
NOTE
Move the chain brake lever (Front hand guard)
fully rearward to remove or install the clutch
cover to chain saw.
1. Remove spark plug lead. (See page 24)
2. Remove two clutch cover nuts and remove clutch
cover.
3. Remove bar and saw chain if necessary. See
“Maintenance and Care” section for guide bar/
saw chain maintenance procedures.
- OPERATOR’S MANUAL 1
- CHAIN SAW 1
- RULES FOR SAFE OPERATION 2
- CONTENTS 3
- SYMBOLS AND SIGNS 3
- SYMBOL FORM 4
- PACKING LIST 5
- NOMENCLATURE OF PARTS 6
- NOMENCLATURE OF PARTS 7
- OPERATOR SAFETY 8
- CORRECT USE OF CHAIN BRAKE 9
- PREPARATION FOR USE 10
- ADJUSTING CHAIN TENSION 11
- FUEL AND LUBRICANT 12
- OPERATION 13
- WHEN THE ENGINE IS WARM 14
- WHEN THE ENGINE IS HARD TO 14
- CHECKING CHAIN TENSION 15
- STOPPING 15
- CHAIN LUBRICATION TEST 15
- CUTTING INSTRUCTION 16
- FELLING THE TREE 17
- DANGER 18
- CHAIN BRAKE OPERATION 19
- TESTING THE BRAKE 19
- AUTOMATIC CHAIN BRAKE 20
- WINTER OPERATION 20
- GUIDE BAR 21
- SAW CHAIN 21
- MAINTENANCE AND CARE 22
- CARBURETOR ADJUSTMENT 23
- AIR FILTER 24
- CHECK FUEL SYSTEM 24
- SPARK PLUG 24
- FUEL FILTER 24
- OIL FILTER 24
- SPROCKET 25
- CYLINDER FINS 25
- MUFFLER SPARK ARRESTOR 25
- AUTOMATIC OILER 25
- SETTING THE SAW CHAIN 26
- TROUBLESHOOTING 28
- STORAGE AFTER USE 29
- TECHNICAL DATA 29
- 10002001/10999999 30
Produits connexes et manuels pour Micro-ondes Sharp R-370ES
Micro-ondes Sharp R-320CD Manuel du propriétaire
(182 pages)
(182 pages)
Micro-ondes Sharp R-9450 Spécifications
(143 pages)
(143 pages)
Micro-ondes Sharp R-330Y Manuel d'instructions
(191 pages)
(191 pages)
Micro-ondes Sharp R-249 Spécifications
(52 pages)
(52 pages)
Micro-ondes Sharp R-27STM Manuel de service
(28 pages)
(28 pages)
Micro-ondes Sharp R-201T Manuel d'instructions
(120 pages)
(120 pages)
Micro-ondes Sharp R-899R Spécifications
(148 pages)
(148 pages)
Micro-ondes Sharp R-662K Manuel de service
(27 pages)
(27 pages)
Micro-ondes Sharp R-420L Spécifications
(30 pages)
(30 pages)
Micro-ondes Sharp R-633 Manuel d'utilisateur
(76 pages)
(76 pages)
AEG Electrolux EFP 60202 manuály
Uživatelské manuály a uživatelské příručky pro Odsavače par AEG Electrolux EFP 60202.
Poskytujeme 1 manuály pdf AEG Electrolux EFP 60202 ke stažení zdarma podle typů dokumentů: Specifikace
Commentaires sur ces manuels