Sharp PC-W100T Manuel d'installation Page 9
- Page / 48
- Table des matières
- DEPANNAGE
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
W100T Twin Alternating Series Softeners 9
User 1
Typical user display. If volume is selected in Configuration Settings
Step 4CS, shows volume remaining to regeneration. If volume is not
selected in Configuration Settings Step 4CS, this screen will not be
shown. If a meter is not used this display will not change.
User 2
Displays number of days to next regeneration.
User 3
Displays flow rate in gallons per minute. If a meter is not used this
display will be shown but 0 will be displayed. If 1.0 is selected in
Step 2CS an “A” in front of the flow rate indicates that the tank with
the control valve on it is in service. If “b” is displayed the tank with the
in/out head is in service.
This screen will not be shown if 7 day or 28 day is selected in
Configuration Settings Step 4CS.
User 4
Displays total flow in gallons since last reset. If a meter is not used this
display will be shown but 0 will be displayed. This screen will not be
shown if 7 day or 28 day is selected in Configuration Settings Step
4CS.
PRESS ▼ FOR 3 SECONDS TO RESET TO 0.
User 5
Shows current time.
B. Setting Time of Day
• Push NEXT until time of day screen is displayed. Press and
hold ▲or ▼ until the SET indicator is displayed, and the hour
flashes. Press ▲or ▼until the correct hour is displayed.
• Then press NEXT. The minutes will flash. Press ▲or ▼until
the correct minute is displayed.
• Press NEXT to return to the Display Screens. Time of day
should only need to be set after power outages lasting more
than 8 hours, if the battery has been depleted and a power
outage occurs, or when daylight saving time begins or ends.
If a power outage lasting more than 8 hours occurs, the time
of day will flash on and off which indicates the time of day
should be reset. If a power outage lasts less than 8 hours
and the time of day flashes on and off, the time of day should
be reset and the battery replaced.
User Displays
A. General Operation
When the system is operating, one of five displays may be shown. Pressing
NEXT will alternate between the displays shown below.
- Table of Contents 1
- System Specification Table 2
- Safety Information 3
- General Warnings 3
- General Warnings (continued) 4
- How To Use This Manual 4
- (continued) 5
- W100T System Programming 6
- Regen Screen 7
- Error Screen 7
- Regeneration Cycles and Times 8
- Button Operation and Function 8
- User Displays 9
- Configuration Settings 10
- Step 6CS 11
- CWS200 Valve 12
- W100T, CWS150 12
- CWS200 Valves 12
- Step 7CS 13
- EXIT TO 14
- DISPLAY 14
- Installer Display Settings 15
- Step 3I 16
- Step 4I 16
- Step 1I 16
- Step 2I 16
- Step 5I 16
- Diagnostics 17
- W100T Part List and Drawings 18
- Valve Body Compliance Table 19
- Twin Transfer 21
- Twin Transfer (continued) 22
- Injector Order Information 24
- Drain Line – 3/4” 30
- Drain Line - 1” 31
- D1400 1191 In/Out Head 33
- Drive Assembly 34
- Spacer Stack Assembly 35
- Service Instructions 37
- Water Meter 40
- Release locking tabs 41
- Seal "Lip" 41
- "A" text orientated 42
- Splines can only 42
- Troubleshooting 43
Produits connexes et manuels pour Carnets de notes Sharp PC-W100T
Carnets de notes Sharp 21H-S3P Spécifications
(413 pages)
(413 pages)
Origin Storage TS-L840D manuals
Owner’s manuals and user’s guides for Unknown Origin Storage TS-L840D.
We providing 1 pdf manuals Origin Storage TS-L840D for download free by document types: Datasheet
Commentaires sur ces manuels