Sharp AR-151 Spécifications Page 87
- Page / 170
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2) Set the test chart so that the scale is positioned as shown below,
in the S-D mode and the D-S mode.
3) Execute simulation 50-18 to make a copy and check the front edge
image loss at the area where the scale is printed.
Adjust the setting so that the front edge image loss is less than 4.0
mm in the R-SPF mode.
An increase of 1 in setting represents an increase of 0.1 mm in
image loss.
B. Adjusting trailing edge void in duplex copy mode
This is the adjustment of the first surface printing mode (rear end void)
in duplex copying.
In a duplex copying operation, the paper is delivered starting from the
rear end of the first printing surface. It is therefore necessary to make
a void area at the rear end on the first printing surface to prevent paper
jam at the fusing part.
There are two adjustment modes:
1) Image cut rear end void quantity (R-SPF) 50-19(AE)
The size (length) of a document read from the R-SPF is detected,
the image at the trailing edge of the first printing surface is cut to
make a void area. (The adjustment of void quantity at the time
when the cassette paper size is not recognized.)
2) Paper trailing edge void quantity 50-19 (TEXT)
This adjustment is made when the cassette paper size is recog-
nized. The trailing edge void quantity can be adjusted by changing
the trailing edge image laser OFF timing.
The paper void quantity should be first adjusted before the image cut
trailing edge void quantity (R-SPF) is adjusted.
(Adjustment procedure)
(1) Paper trailing edge void quantity
1) Preparing test chart (Draw a scale at the rear end of one side of
a sheet of A/4 white paper or letter paper)
2) Set the test chart on the document glass as shown below.
3) Using the user simulation [18], set the paper size of the first cas-
sette.
Letter paper: 4
A4 paper: 3
4) Execute simulation 50-19 to turn on the TEXT lamp and make the
printing mode in OC-D mode.
Make a copy of the test chart to check the void area of the scale
on the image.
Adjust the setting so that the void area is 4 - 5 mm.
An increase in 1 of setting represents 0.1 mm in void area.
(2) Image cut trailing edge void quantity (R-SPF)
1) Set the test chart so that the scale is positioned as shown below.
2) Execute simulation 50-19 to turn on the AE lamp and make the
printing mode in the D-D mode.
3) Remove and reinsert the cassette.
NOTE: Make sure to carry out this step before making a copy
during this adjustment.
4) Make a copy and check the void area of the scale on the image.
Adjust the setting so that the void area is 2 - 4 mm.
An increase of 1 in setting represents an increase of 0.1 mm in
void area.
Scale (S-D mode) Scale (D-S mode)
510
The front edge of the
scale on test chart
Front edge of paper
Void area
less than 4 mm
2nd printing surface where scale is printed (lower side)
Document guide
The trailing edge has a scale
Table glass
Scale (D-D mode)
The trailing edge void on the first printing surface
is shown above.
Paper
Void position to be check
AR-F152
8 – 10
- DIGITAL COPIER 1
- VORSICHT 2
- ADVARSEL 2
- VARNING ! 2
- [1] GENERAL 4
- [2] SPECIFICATIONS 5
- C. Copy performance 6
- [3] CONSUMABLE PARTS 16
- 2. Environmental 17
- 4. TD cartridge replacement 18
- 1. Appearance 19
- 2. Internal 19
- 3. Operation panel 20
- 191817161514 20
- FAX STARTSTOP 21
- 5. Motors and solenoids 22
- 6. Sensors and switches 23
- 7. PWB unit 24
- 8. Cross sectional view 25
- 1. COPIER INSTALLATION 26
- 2. CAUTIONS ON HANDLING 26
- 8. LOADING COPY PAPER 28
- Paper guide (B) 29
- Paper guide (A) 29
- [6] OPERATIONAL DESCRIPTIONS 30
- 2. Scanner section 31
- 3. Laser unit 31
- 4. Fuser section 32
- A. Outline 36
- C. Operational descriptions 37
- A. Initial state 38
- B. Front copy 38
- C. Back copy 38
- Communicatinon error flag ON 39
- Response received? 40
- Command received? 42
- Auto dial sending 43
- [7] DISASSEMBLY AND ASSEMBLY 44
- C. Disassembly procedure 46
- D. Assembly procedure 46
- E. Charger wire cleaning 46
- 2. Operation panel section 47
- 3. Optical section 48
- 4. Fusing section 49
- B. Disassembly procedure 49
- PPD2 sensor 50
- Heat roller 51
- CAUTION:Attach 54
- 6. Manual paper feed section 56
- Wire treatment 57
- 7. Rear frame section 60
- 8. Power section 61
- 9. SPF section 61
- A. Sensor PWB 62
- B. Pickup solenoid 62
- C. Clutch 62
- F. SPF motor 63
- G. Paper entry sensor 63
- 10. 2nd cassette section 64
- B. Cassette detection SW 65
- C. Paper feed solenoid 65
- D. Transport roller 65
- E. Paper feed clutch 65
- F. 2nd paper feed roller 65
- B. Intermediate tray 67
- C. Upper cover 67
- D. Pickup unit 68
- F. Sensor PWB 68
- G. Pickup solenoid 68
- H. Clutch 69
- J. Transport unit removal 70
- K. Belt 1 70
- L. Belt 2 70
- M. SPF motor 70
- N. Solenoid 70
- O. Clutch 71
- P. PS roller 71
- Q. Paper entry sensor 71
- R. Transport roller1 72
- S. Paper exit roller 72
- 14. FAX, MCU PWB section 73
- (AR-F152 only) 73
- D. Remove the PWB cover FAX 74
- E. Remove the MCU PWB 74
- B. Remove the metal fixtures 74
- ROM (AR-F152 only) 77
- [8] ADJUSTMENT 78
- Set screw 79
- Scanner unit drive pulley 79
- Copy lamp unit projection 79
- Image distortion check chart 79
- Document 80
- Greater distortion 80
- Smaller distortion 80
- Copy image dimension 82
- Original dimension 82
- D. Image position adjustment 83
- B4 or 8 1/2″ × 14″ paper 84
- A4 size rear edge 84
- 2. Copy density adjustment 85
- 3. High voltage adjustment 86
- 4. Duplex adjustment 86
- Scale (D-D mode) 87
- 5. Density section 88
- 6. Communication section 89
- 1. List of simulations 90
- AE, Main cassette lamp 101
- AE lamp (Blinking) 101
- AE, TEXT lamp 101
- AE, TEXT, PHOTO lamp 101
- B. List of functions 103
- A. Software Switch List 109
- 5. TROUBLE CODES 118
- (1) Sending error 119
- (2) Reception error 119
- (1) LCD: FAX SERVICE ERROR(#) 119
- [10] USER PROGRAM 120
- [11] MAINTENANCE 121
- [12] ELECTRICAL SECTION 122
- B. MCU PWB unit 123
- FAX PWB UNIT 124
- 2. Circuit descriptions 125
- (2) ASIC (Signal table) 127
- LCD PWB 134
- NSFX200 (IC503) supplies 135
- Input Signals 135
- Output Signals 135
- Input/Output Signals 136
- (2) NS32FX164 (IC507) 136
- Input-Output Signals 137
- (4) CPU interface 138
- (5) Image memory interface 138
- (6) Others 138
- Motor control 140
- Bus control 140
- LBP module 141
- 6. LCD circuit (AR-F152 only) 142
- C. LCD panel pin arrangement 143
- [13] CIRCUIT DIAGRAM 144
- MCU 2 (INPUT SECTION) 145
- MCU 3 (OUTPUT SECTION 1) 146
- MCU 4 (OUTPUT SECTION 2) 147
- MCU 5 (ASIC SECTION) 148
- MCU 7 (CONNECTOR SECTION 2) 150
- MCU 8 (CONNECTOR SECTION 3) 151
- FAX LCD PWB (AR-F152 Only) 162
- ACTUAL WIRING DIAGRAM 1/5 164
- ACTUAL WIRING DIAGRAM 2/5 165
- ACTUAL WIRING DIAGRAM 3/5 166
- ACTUAL WIRING DIAGRAM 4/5 167
- ACTUAL WIRING DIAGRAM 5/5 168
- SHARP CORPORATION 170
Produits connexes et manuels pour Copieurs Sharp AR-151
Copieurs Sharp AR-5220 Manuel d'utilisateur
(88 pages)
(88 pages)
Copieurs Sharp SF-2530 Manuel d'utilisateur
(34 pages)
(34 pages)
Copieurs Sharp AR-C360P Spécifications
(181 pages)
(181 pages)
Copieurs Sharp MX-M283 Manuel d'utilisateur
(12 pages)
(12 pages)
Copieurs Sharp JH-1600E Manuel d'utilisateur
(13 pages)
(13 pages)
Copieurs Sharp AR-M276 Manuel d'utilisateur
(24 pages)
(24 pages)
Copieurs Sharp AR-NB3 Spécifications
(41 pages)
(41 pages)
Copieurs Sharp AR-5316 Spécifications
(56 pages)
(56 pages)
Copieurs Sharp SF-2414 Manuel d'utilisateur
(43 pages)
(43 pages)
Hunter-fan 40135 Handbücher
Bedienungsanleitungen und Benutzerhandbücher für Schalttafel Hunter-fan 40135.
Wir stellen 1 PDF-Handbücher Hunter-fan 40135 zum kostenlosen herunterladen nach Dokumenttypen zur Verfügung Bedienungsanleitung
Hunter fan 40135 Bedienungsanleitung (30 Seiten)
Marke: Hunter-fan | Kategorie: Control panel | Größe: 1.14 MB |
Inhaltsverzeichnis
Y / C* / M
10
Wall Plate
12
HE/HG Switch
17
HG for a gas
18
Note: In
21
Span Adjust
23
Heat 24V or
28
Weitere Produkte und Handbücher für Schalttafel Hunter-fan
| Modelle | Dokumententyp |
|---|---|
| 47350A |
Bedienungsanleitung
Hunter Fan 47350A User Manual,
23 Seiten
|
| 44260 |
Bedienungsanleitung
Hunter Fan 44260 User Manual,
104 Seiten
|
| 44377W |
Bedienungsanleitung
Hunter Fan 44377W User Manual,
64 Seiten
|
| PH20-30A |
Bedienungsanleitung
Hunter Fan PH20-30A User Manual,
26 Seiten
|
| 40170 |
Bedienungsanleitung
Hunter Fan 40170 User Manual,
33 Seiten
|
| 44550 |
Bedienungsanleitung
Hunter Fan 44550 User Manual,
38 Seiten
|
| 44459 |
Bedienungsanleitung
Hunter Fan 44459 User Manual,
40 Seiten
|
| 43665 |
Bedienungsanleitung
Hunter Fan 43665 User Manual,
49 Seiten
|
| 44360 |
Bedienungsanleitung
Hunter Fan 44360 User Manual,
58 Seiten
|
| 44660 |
Bedienungsanleitung
Hunter Fan 44660 User Manual,
2 Seiten
|
| SET & SAVE 44155C |
Bedienungsanleitung
Hunter Fan SET & SAVE 44155C User Manual,
52 Seiten
|
| 144860 |
Bedienungsanleitung
Hunter Fan 144860 User Manual,
76 Seiten
|
| 47110A |
Bedienungsanleitung
Hunter Fan 47110A User Manual,
2 Seiten
|
| 43157 |
Bedienungsanleitung
Hunter Fan 43157 User Manual,
2 Seiten
|
| 47250A |
Bedienungsanleitung
Hunter Fan 47250A User Manual,
7 Seiten
|
| 42999 44050S |
Bedienungsanleitung
Hunter Fan 42999 44050S User Manual,
23 Seiten
|
| 47200A |
Bedienungsanleitung
Hunter Fan 47200A User Manual,
7 Seiten
|
| 44428 |
Bedienungsanleitung
Hunter Fan 44428 User Manual,
22 Seiten
|
| 42177 |
Bedienungsanleitung
Hunter Fan 42177 User Manual,
25 Seiten
|
| 42711-01 |
Bedienungsanleitung
Hunter Fan 42711-01 User Manual,
55 Seiten
|
© 2020, manymanuals.fr. Tous droits réservés | 0.039 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels