Sharp R-23AM Manuel de service télécharger pdf (Page 12)

R-22AT

R-23AM

R-24AT

Room temperature ................................................................................................. T0 = 21°C

Initial temperature .................................................................................................. T1 = 11°C

Temperature after (28 + 3) = 31 sec [for R-22AT].................................................. T2 = 21°C

Temperature after (22 + 3) = 25 sec [for R-23AM/24AT] ....................................... T2 = 21°C

Temperature difference Cold-Warm......................................................................∆T1 = 10˚C

Measured output power

The equation is “P = 150 x ∆T” [for R-22AT] ........................... P = 150 x 10°C = 1500 Watts

The equation is “P = 190 x ∆T” [for R-23AM/24AT] ................ P = 190 x 10°C = 1900 Watts

JUDGMENT: The measured output power should be within the range of ± 15 % of the rated output

power.

CAUTION: 1°C CORRESPONDS TO 150 WATTS [R-22AT]/ 190 WATTS [R-23AM, R-24AT]. REPEAT

MEASUREMENT IF THE POWER IS INSUFFICIENT.

TEST PROCEDURES

PROCEDURE

LETTER COMPONENT TEST

1000g

T1˚C

T2˚C

Heat up for 31 sec. for R-22AT

Heat up for 25 sec. for R-23AM/ R-24AT

MICROWAVE OUTPUT POWER (2000 cc alternative method)

The power output of this oven is rated using the method specified by IEC 60705. Full details of how

to curry out this procedure can be found in the Sharp Technical Training notes which is available from

Sharp Parts Centre (part number SERV-LITMW01).

The IEC-60705 procedure must be carried out using laboratory-type procedures and equipment.

These requirements make the procedure unsuitable for routine performance checks.

NOTE: The following test method gives an indication of the output power only, it cannot be used to

establish the actual/rated output power. If the true output power is required, then the IEC60705

test method must be used.

Alternative simplified method:

1. Place 2 litres of cold water (between 12°C and 20°C) in a suitable container.

2. Stir the water and measure the temperature in °C. Note temperature as T1.

3. Place the container in the microwave and heat the water for 56 sec. [R-22AT]/ 44 sec. [R-23AM,

R-24AT] on fill power.

4. When the 56 sec. [R-22AT]/ 44 sec. [R-23AM, R-24AT] is completed, remove the container and

stir the water. Note temperature as T2.

5. Calculate the output power using the following formula:

R.F. Power Output = (T2 - T1) x 150 for R-22AT.

R.F. Power Output = (T2 - T1) x 190 for R-23AM, R-24AT.

NOTE: The result from this test should be within the allowance of 2000cc alternative method.

(±10%).

MICROWAVE LEAKAGE TEST

This oven should be tested for microwave leakage on completion of any repair or adjustment, following

the procedure described in the Sharp Technical Training notes (part number SERV-LITMW01). The

maximum leakage permitted in BS EN 60335-2-25 is 50W/m

(equivalent to 5W/m

), however it is not

normal to detect any significant leakage, therefore, any leakage which is detected should be

investigated.

It is essential that only leakage detectors with current calibration traceable to National Physical

Laboratories are used.

Suitable leakage detectors: CELTEC A100

APOLLO X1

1 2 ... 7 8 9 10 11 12 13 14 15 16 17 ... 55 56

Commentaires sur ces manuels

Pas de commentaire

Sharp R-23AM Manuel de service Page 12

Commentaires sur ces manuels

Produits connexes et manuels pour Micro-ondes Sharp R-23AM